Accès aux paramètres internes du NOM M340

Exemple de code:
if dataCh010Get then
read_var(addm(‘0.1.0’), ‘%MW’, dataCh010StartAddr, dataCh010Size, dataCh010Mgt, dataCh010Buff);
dataCh010Get := false;
end_if;

Contenu de la zone:

Address	Field kind	Designation
%MW0	INT	Tx Start Delay: wait a delay before sending data. It is commonly used with the half duplex modem mode to set the RTS signal, wait the CTS signal and then wait this delay before sending data. It seems to conform to FOCKS mechanism.
%MW1	INT	Tx End delay: wait a while after the last byte sent. It is commonly used with half duplex modem mode to maintain the RTS signal this time, to let enougth time to the modem to send the buffer to the peer, before switching to reception mode. It seems to conform to the FOCKS mechanism.
%MW16	INT	bus_message_count
%MW18	INT	bus_com_error_count
%MW20	INT	bus_except_error_count
%MW22	INT	slave_mes_count
%MW24	INT	slave_no_resp_count
%MW26	INT	slave_NAK_count
%MW28	INT	slave_busy_count
%MW30	INT	bus_char_overrun_count
%MW30	INT	Internal com_event_count
%MW30	INT	Internal diag_register
%MW30	INT	Internal successfull_mstr_count
%MW30	INT	Internal successfull_slave_count
%MW40	INT	Internal bad_adr_count
%MW42	INT	Internal bad_length_count
%MW44	INT	Internal mstr_retry_count
%MW46	INT	Internal STOP_BYTES
%MW48	INT	Internal listenOnlyMode
%MW50	INT	Internal KindOfFlowControl (0:full duplex, 1 RTS, 2 DTR)
%MW100	INT	Internal conf mode
%MD102	DINT	Internal conf baudrate
%MW104	INT	Internal conf dataLength
%MW106	INT	Internal conf parity
%MW108	INT	Internal conf stopBitNb
%MW110	INT	Internal conf rs232
%MW112	INT	Internal conf hwFlowCtrl
%MW114	INT	Internal conf modemMode
%MW116	INT	Internal conf framesDelay
%MW118	INT	Internal conf silence
%MW120	INT	Internal conf slaveAnswerDelay
%MW122	INT	Internal conf slaveNumber
%MW124	INT	Internal conf slaveNumberExternal
%MW126	INT	Internal conf polarizationModbus
%MW128	INT	Internal conf polarizationUnitelway
%MW130	INT	Internal conf nbRetries
%MW132	INT	Internal conf rtsCtsTimeout
%MW134	INT	Internal conf endOfFrameChar1
%MW136	INT	Internal conf endOfFrameIncludedChar1
%MW138	INT	Internal conf endOfFrameByteChar1
%MW140	INT	Internal conf endOfFrameChar2
%MW142	INT	Internal conf endOfFrameChar2
%MW144	INT	Internal conf endOfFrameIncludedChar2
%MW146	INT	Internal conf endOfFrameByteChar2
%MW148	INT	Internal conf blindTimeMs
%MW150	INT	Internal usePatchedTimings
%MW152	INT	Internal t3_5ch
%MW154	INT	Internal t1_5ch
%MW156	INT	Internal tDelay
%MD158	DINT	Internal conf KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW160	INT	Internal conf ctsDelayBeforeTx : In half duplex mode, on sending, the RTS signal raise, then when the CTS raise the delay is executed beforte sending the frame.
%MW162	INT	Internal conf rtsDelayAfterTx: In half duplex mode, after sending, the RTS signal is maintain until the delay is over.
%MW200	INT	Current version of the local channel server (00.01)
%MW201	INT	Flash Slave Address
%MW202	INT	Is it authorized to change the address ?
%MW1000	INT	Modbus RTU Master: internal protocol code
%MW1002	INT	Modbus RTU Master: KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW1010	INT	Modbus RTU Master: T1_5crS
%MW1012	INT	Modbus RTU Master: T1_5crR
%MW1014	INT	Modbus RTU Master: T3_5crS
%MW1016	INT	Modbus RTU Master: T3_5crR
%MW1018	INT	Modbus RTU Master: DelayInBits
%MW1090	INT	Modbus RTU Master: nb retries configured
%MW1100	INT	Modbus RTU Master: SlaveAnswerDelay10ms Broadcast
%MW1101	INT	Modbus RTU Master: SlaveAnswerDelay10ms Slave 1
%MW1102	INT	Modbus RTU Master: SlaveAnswerDelay10ms Slave 2
%MW1103	INT	…
%MW1347	INT	Modbus RTU Master: SlaveAnswerDelay10ms Slave 247
%MW1348	INT	Modbus RTU Master: SlaveAnswerDelay10ms Point to Point
%MW1500	INT	Modbus RTU Slave: internal protocol code
%MW1502	INT	Modbus RTU Slave: KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW1510	INT	Modbus RTU Slave: T1_5crS
%MW1512	INT	Modbus RTU Slave: T1_5crR
%MW1514	INT	Modbus RTU Slave: T3_5crS
%MW1516	INT	Modbus RTU Slave: T3_5crR
%MW1518	INT	Modbus RTU Slave: DelayInBits
%MW1600	INT	Modbus RTU Slave: SlaveAddr
%MW1602	INT	Modbus RTU Slave: BlindTimeAfterReception
%MW1604	INT	Modbus RTU Slave: blindTimeActivated
%MW1606	INT	Modbus RTU Slave: ListenOnlyMode
%MW2000	INT	Modbus ASCII Master : internal protocol code
%MW2002	INT	Modbus ASCII Master : KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW2010	INT	Modbus ASCII Master: T1_5crS
%MW2012	INT	Modbus ASCII Master: T1_5crR
%MW2014	INT	Modbus ASCII Master: T3_5crS
%MW2016	INT	Modbus ASCII Master: T3_5crR
%MW2018	INT	Modbus ASCII Master: DelayInBits
%MW2090	INT	Modbus ASCII Master: nb retries configured
%MW2100	INT	Modbus ASCII Master: SlaveAnswerDelay10ms Broadcast
%MW2101	INT	Modbus ASCII Master: SlaveAnswerDelay10ms Slave 1
%MW2102	INT	Modbus ASCII Master: SlaveAnswerDelay10ms Slave 2
%MW2103	INT	…
%MW2347	INT	Modbus ASCII Master: SlaveAnswerDelay10ms Slave 247
%MW2348	INT	Modbus ASCII Master: SlaveAnswerDelay10ms Point to Point
%MW2500	INT	Modbus ASCII Slave: internal protocol code
%MW2502	INT	Modbus ASCII Slave: KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW2510	INT	Modbus ASCII Slave: T1_5crS
%MW2512	INT	Modbus ASCII Slave: T1_5crR
%MW2514	INT	Modbus ASCII Slave: T3_5crS
%MW2516	INT	Modbus ASCII Slave: T3_5crR
%MW2518	INT	Modbus ASCII Slave: DelayInBits
%MW2600	INT	Modbus ASCII Slave: SlaveAddr
%MW2602	INT	Modbus ASCII Slave: BlindTimeAfterReception
%MW2604	INT	Modbus ASCII Slave: blindTimeActivated
%MW2606	INT	Modbus ASCII Slave: ListenOnlyMode
%MW3000	INT	Char Mode: internal protocol code
%MW3002	INT	Char Mode: KindOfFlowControl (0: none, 1: RTS automatic, 2: DTR automatic instead of RTS)
%MW3100	INT	Char Mode: Stop criteria present
%MW3102	INT	Char Mode: Ticr
%MW3104	INT	Char Mode:  EOF byte 1
%MW3104	INT	Char Mode:  EOF char 1 added
%MW3104	INT	Char Mode:  EOFbyte 2
%MW3104	INT	Char Mode:  EOF char 2 added